Shimano's SM-SH56 Multi-Release Cleats disengage with less effort and in more directions than standard SPD cleats. - Not compatible with Shimano PD-M858 (XTR) SPD pedals

Protect the soles of your shoes with the Shoe Shields from Crank Brothers. These stainless-steel plates install under your cleats and prevent the pedal from digging in to your carbon-soled shoes. - Sold in pairs

Problem Solvers Deckster pedal adapters. Converts SPD-compatible pedals to platform pedals for casual cruising. - Works with 2-bolt, SPD-style cleats, such as Time, Shimano, Crank Brothers, Wellgo and others. Not compatible with Speedplay - Cleats not included - 85 x 95 x 10mm platform - Hardware included, cleats not included

Get that fresh cleat feel These solidly-built cleats work with Bontrager road pedals or any Look Cycle’s KÉO-compatible clipless pedals. Whether you're looking for replacements, need a new set for a new pair of kicks, or just like to keep an extra pair in your toolkit. Product details - Replacement cleats for all Look Cycle’s KÉO®-compatible road pedals - Directly compatible with Bontrager Comp Road pedals - Set includes 1 pair

- Set of 44 total replacement steel pins for vault pedals - Run threads-out for maximum traction or flip the pins to heads-out for less grip - 16 Short pins (for use in the center) overall length 8.5mm, stud is 4.5mm - 28 Long pins (for use in the outside edge) overall length 12.5mm, stud is 4.5mm - Use either a 5mm spanner or the included 2mm hex wrench to secure/remove

Longer rear load pins for the outer extremities of your pedals provide ultimate durability, while shorter front load center pins create a virtual concavity in the pin pattern, increasing grip without sacrificing pedal body thinness. - 28pcs rear load pins - 16pcs front load pins - Tool included

- Cleats to fit Ritchey Echelon and Look Keo clipless pedals - Includes a pair of cleats and hardware

IGUS Bushing replacements for your Spike or Oozy pedals help to eliminate any play that develops over time, and revive smooth spinning action. - 2pcs IGUS self lubricating bushing - 2pcs O-ring - 2pcs stainless shim washer

Dimension Toe Clips and Straps Set. Includes: - 4 bolts - 4 nuts (washers included) - 2 nylon toe straps - 2 toe clips

A revolution in performance and reliability. The kit includes premium internal components: - Enduro catridge bearings - Enduro sealed needle bearing - Double seal system (internal and external seals) - Hex alloy end caps - O-rings, nuts - Sleeve bushings - Bearing removal tool

Crank Brothers' Premium MTB Cleats are perfect for your Crank Brothers Eggbeater, Candy, Acid, Smarty, Mallet and Quattro pedals. They're made from solid brass for crisp entry and exit and top-notch durability.

- Look, Kéo 2 Max, Blades

Cleats with a more forgiving 10-deg release. - Optimized for novice riders or those new to clip-in pedals - 10-deg release angle makes it easier to unclip - 2-hole bolt pattern for mountain bike shoes - Plastic spacing shims included - Compatible with all Crankbrothers clip-in pedals

The KEO GRIP cleats closely resemble the KEO CLEAT model, yet they boast the added feature of a TPU layer on the shoe side which prevents the risk of cleats sliding on carbon soles. Their anti-slip surface on the pedal side offers extra safety and stability when walking. - Use: Road - Material: Polyamide + TPU - Lateral adjustment: 4mm - Longitudinal adjustment: 9mm - Weight (pair + fasteners): 68g

The Ergon TP1 Pedal Cleat Tool is the first tool for precisely and easily adjusting cycling shoes cleats. The ergonomically correct position of the feet on the pedals plays a crucial role in injury prevention and is also important for maximizing both performance and comfort.

Eliminate cleat wear and improve walking comfort and safety with these Exustar cleat covers. - Compatible with Exustar cleat C01, C03, and C05 - Durable and flexible rubber - Can be used with either floating or fixed position cleats - Weight of only 14 grams/pair

- Extends pedals - Not for use on exercise bikes

iSSi's SPD cleats are perfect for all your SPD-compatible pedals. If your entry and exit isn't what it used to be, a cleat replacement is just what the bike doctor ordered. - 4 degrees of float both inward and outward

Your pedals like to be pampered. The Crank Brothers Pedal Refresh Kit gives you everything you need to keep them happy. Pedal Refresh Kit includes: -Enduro catridge bearings - Igus LL-glide bearings - Double seal system (internal and external seals) - Hex alloy end caps - O-rings - Nuts - Sleeve bushings - Bearing removal tool Compatible with the following pedals (2010-present): - Eggbeaters - Candys - Mallets - 5050s

Pre-cut traction tabs designed to integrate with the Highline remote lever and increase grip for ultimate control.

Engineered to optimize the interface between the pedal and shoe for ultimate performance and power transfer. The kit includes: - 8 × 1mm traction pads - 8 × 2mm traction pads Compatible with: - Mallet E - Model years 2016 – present

- Works with all XPRO and XPRESSO pedals. - Not included with new XPRO and XPRESSO pedals. - This is a zero-float cleat design, so there are zero (0) degrees of heel float and no lateral float along the pedal axle. - Compatible with all three-hole road shoes, but the included shim may be required for shoes that have a large curvature in the forefoot area. Full details are included in the easy-to-use instructions.

The DELTA standard requires a rotational movement of the foot toward the outside or inside for disengagement. This function improves cyclist's safety; no body or bearing prevents disengagement toward the inside. Compatible with non-KEO LOOK pedals, their contact area is wide for optimal comfort. They also feature a memory positioner to aid when changing cleats. - Use: Road & Indoor Bike - Material: Polyacetal + PTFE - Lateral adjustment: 4mm - Longitudinal adjustment: 12mm - Weight (pair + fasteners): 75g

Authentic Ritchey replacement cleats for WCS Micro Road Pedals. Note: only Ritchey replacement cleats work with the Micro pedal. - Beveled cleat compatible with Ritchey WCS Micro pedals - Compatible with SPD style pedals

The Activ Grip Trail Pads are compatible with our Trail Grip platform pedals. Built from extremely strong and durable material and designed in collaboration with outdoor specialist Vibram, they offer exceptional traction on the toughest rides. Their concave geometry is enhanced with large rubber lugs and composite studs for optimal foot stability and extreme durability to take on the challenges of any terrain.

Cleat screws are intended for proper installation of the Cleat Wedge. Designed to withstand high torque levels, creating a secure and reliable connection between the rider and the bike. Available in different lengths and styles to fit most pedal systems. - 10mm SPD/MTB compatible cleat screws - 4mm Hex countersunk M5x0.8 - Compatible with most 2-hole cleats - Black oxide-coated carbon steel - 25 pieces

The MADE by LOOK KEO standard is recognized in the cycling world for its minimal weight and compact design of the cleat and pedal combo. Of course, compatible with all pedals on the market, their memory positioner is a major advantage when changing your cleats. Their principle and use are the same as the DELTA cleat standard; engagement and disengagement remain efficient and reassuring. - Use: Road - Material: Polyamide + PTFE - Lateral adjustment: 4mm - Longitudinal adjustment: 12mm - Weight (pair + fasteners): 68g

- Shimano SPD-SL-style - Engineered thermoplastic injection body - Weight of 24 grams per cleat - 4.5-degree floating arc

- Nylon construction - Intended for use with double-strap toe straps (sold separately) - Includes mounting hardware - 36 grams per pair

- Developed for the TIME XPRO & XPRESSO road bike pedal range. - They allow angular and lateral freedom in order to respect the natural movements of your legs and joints. - You can also adjust the Q-factor (by switching the cleats) - The Bi-material brings more durability when walking with the cleats. - These cleats are the stock cleats included with all XPRO & XPRESSO pedals.